FOXBORO FBM223 Dual PROFIBUS-DP Master Communication Interface Module I A Series Compact 200 DCS

Manufacturer: FOXBORO (Schneider Electric Process Automation)

Part Number: FBM223 (Hardware PN P0916KN; FDSI field device interface series, dual PROFIBUS-DP master gateway)

Product Type: PROFIBUS-DP V0/V1 dual master communication bridge FBM, non-analog digital communication module, simplex/master-tracker hot redundant rack compatible, integrates third-party DP slave instruments & drives into I/A DCS

Matching Platform: Foxboro I/A Series DCS, MESH fiber control network, FCM100E redundant fieldbus gateway, ZCP270/ZCP280 process controllers, dedicated PROFIBUS TA termination base, PROFIBUS shielded bus cable, DIN rail modular Compact 200 baseplate

Core Function: Two independent galvanically isolated PROFIBUS-DP master channels; each segment supports max 31 DP slave devices; auto baud rate detection 9.6kbit/s ~ 12Mbit/s; full DP V0 cyclic real-time process data exchange + DP V1 acyclic parameter read/write & device diagnostic; full bus fault diagnosis (bus short, open wire, slave loss, baud mismatch); maps all slave AI/AO/DI/DO & fault alarms to I/A control database; dual redundant 2Mbps HDLC backplane communication to FCM gateway; bumpless millisecond hot redundant switchover paired with second FBM223; front panel multi-color LED array for RUN, BUS1, BUS2, FAULT status; ISA G3 harsh industrial PCB; optional anti-salt-fog conformal coating for offshore Zone2/Div2 hazardous environments; single-width Compact FBM hot-swap replaceable

1. Product Overview

FBM223 belongs to Foxboro Compact 200 FDSI Field Device Interface communication module family, serving as a dual-channel PROFIBUS-DP master gateway to connect external PROFIBUS-DP slave field equipment to I/A Series DCS control system. Unlike analog I/O FBM modules (FBM201/FBM202/FBM204), it specializes in industrial field bus protocol conversion, widely used in petrochemical, power, cement and offshore projects with mass DP drives, transmitters and remote I/O stations. Equipped with two fully isolated independent PROFIBUS-DP master ports, each bus segment can carry up to 31 slave devices without repeaters; supports full PROFIBUS-DP V0 cyclic real-time data transmission for fast control loops and DP V1 acyclic communication for instrument parameter modification, calibration and advanced fault diagnosis. Automatic baud rate identification eliminates manual bus speed configuration errors, supporting full range standard DP transmission rates from 9.6k to 12Mbps. Built-in comprehensive bus layer self-diagnosis continuously monitors bus short-circuit, open circuit, slave offline, terminal resistor missing and baud rate mismatch faults; all fault signals are uploaded to DCS HMI synchronously with front panel LED indicators for rapid on-site bus troubleshooting. The module completes bidirectional data mapping between DP slave registers and I/A internal control points, enabling upper-level controllers to read field measurement values and output regulating commands to variable frequency drives, valve controllers and DP remote I/O seamlessly. Supports master-tracker hot redundant pairing: two FBM223 modules work in redundant mode on the same baseplate, synchronously scanning two PROFIBUS bus segments; if primary communication module fails, the standby unit takes over all DP bus data transmission within milliseconds without bus communication interruption, eliminating single-point communication failure risk for critical production lines. Dual redundant 2Mbps HDLC backplane links connect to upstream FCM fieldbus gateway; slim single-width mechanical design saves cabinet slot space, matched with dedicated PROFIBUS shielded twisted-pair bus wiring and special TA termination base for bus terminal resistor layout. Compliant with ISA S71.04 Class G3 harsh industrial standard, resistant to dust, high humidity and mild chemical vapors; optional IPC-CC-830 anti-corrosion PCB coating is available for salt-fog offshore hazardous control rooms. This FBM223 dual PROFIBUS-DP master communication module is standard spare communication hardware for mixed bus I/A Series DCS cabinets, used for new cabinet construction, legacy system DP bus expansion and aged communication module fault replacement maintenance.

Write a review

Your Name

Your Review

Rating

Continue